- Drawing a piling house with softplan 2016 how to#
- Drawing a piling house with softplan 2016 full#
- Drawing a piling house with softplan 2016 software#
Check this link to know more about the pile cap’s code recommendations. But, bear in mind that all of your geometric assumptions should have a basis and at least according to codes and standards.
![drawing a piling house with softplan 2016 drawing a piling house with softplan 2016](https://www.drawingtutorials101.com/drawing-tutorials/Cartoon-TV/Uncle-Grandpa/dirt-pile/how-to-draw-Dirt-Pile-from-Uncle-Grandpa-step-1.png)
![drawing a piling house with softplan 2016 drawing a piling house with softplan 2016](http://www.su-asia.com/images/lakehouse-rendered-wider.png)
Drawing a piling house with softplan 2016 full#
As a designer, you have the full control and can decide over the best types that are suited according to working loads that each column and walls carry. The next step to consider is to decide which type of pile cap to use. The surface loads such as dead loads and live loads that the pile cap will carry are optional when required. The ETABS load combinations will be imported as well. Once you completed the export and import option, all the total vertical and horizontal point loads carried by each column and walls generated by ETABS analysis will be imported. In SAFE, Go to File>Import> SAFE f2k file>Locate the folder location of the f2k file>Open.įigure 1.1: Imported Column and Wall Loads from ETABS
Drawing a piling house with softplan 2016 how to#
Or get through our YouTube channel for the tip on how to export an ETABS model for foundation modeling and design in SAFE. In ETABS, Go to File>Export>Story as SAFE V12 f2k file choose “ BASE” as Story to Export and tick Loads and Export Floor Loads and Loads from Above. Here is how to do it: To create SAFE f2k file and to export from ETABS: In this example, it is assumed that we have already an ETABS analyzed model ready. To be able to perform this, we need to create first a SAFE f2k file. Another way of obtaining the wall and column loads needed in the design is through ETABS export and SAFE import option.
Drawing a piling house with softplan 2016 software#
This time ETABS software is capable of doing so. Structural Engineers often uses a 3D analysis model of the proposed project to capture vertical and lateral forces obtained from dynamic analysis. READ ALSO: Retaining Wall: A Design Approach These are the soil parameters needed in pile cap design among others. Their report will specify the allowable bearing capacity and allowable foundation settlements, allowable capacities under working loads of the recommended diameter of piles, the vertical and lateral pile stiffness or spring constant and the modulus of subgrade reaction.
![drawing a piling house with softplan 2016 drawing a piling house with softplan 2016](https://thumbs.dreamstime.com/b/house-stilts-water-hand-drawn-40160710.jpg)
Once the soil investigation has been completed, the soil laboratory will confirm and recommend the use of pile caps. Though the structural engineer can initially decide if the pile cap is needed at the early stage of design through other considerations as discussed in the previous article, a soil investigation report should confirm otherwise. The allowable bearing capacity usually dictates if a pile cap foundation is required. A geotechnical investigation report is then be submitted by the authorized soil laboratory. The considerations of pile cap to use in foundation design were determined through the series of tests and investigations on the soil profile and characteristics from where the project is located.
![drawing a piling house with softplan 2016 drawing a piling house with softplan 2016](http://softplan.com/forum/uploads/monthly_08_2015/post-25-0-43642500-1440636309.jpg)
When to Consider a Pile Cap in Foundation Design? The common types of pile cap use in the construction are differentiated according to the following images: CSI SAFE, Pile Design, Pile Design in SAFEĪs previously discussed in our article Pile Cap Design Assumptions and Recommendations, Pile Cap is a type of foundation that composed of thick concrete slab built on top of piles used to transmit the load of the structure into the hard strata of the soil.